News
You are here: Home » News

Blogs

11 - 11
DATE
2026
Temperature Rating Selection for Magnetic Encoder Disks Under High/Low-Temperature Conditions: Injection-Molded Ferrite Vs. Rubber Magnet—Don’t Just Look at The Word “Ferrite”
After a collaborative robot runs continuously for several hours, its position feedback begins to drift slowly. When the joint is disassembled, the magnetic encoder disk looks intact, and its magnetization shows no obvious abnormality, but when it is retested at room temperature, the angular error do
Read More
11 - 11
DATE
2026
New Energy Main Drive Motor Resolver Sensor Selection: Five Engineering Judgments That Are Easy To Underestimate
For position sensor selection in main drive motors, the resolver is almost unavoidable. But “choosing a resolver” itself is not difficult. What is difficult is making the few judgments behind the datasheet that truly determine mass-production performance: whether the pole pairs match the motor, how
Read More
06 - 11
DATE
2026
Surface-Mounted High-Speed Rotor Magnet Retention: Why “the Adhesive Will Hold It” Is The Most Dangerous Illusion
In a high-speed permanent-magnet motor running at more than 20,000 rpm, every magnet on the rotor periphery experiences a centrifugal force dozens of times its own weight. If the designer assumes that “a better adhesive will hold it,” the result is often that at some point in durability testing the
Read More
06 - 11
DATE
2026
Load-to-Motor Inertia Ratio for Frameless Torque Motors: From “Stability Shackles” To A “Yardstick for Acceleration Capability”
In traditional servo selection, the inertia ratio is often treated as a red line: exceed the recommended value, and the system may oscillate, overshoot, or become difficult to stabilize. However, when the actuator is replaced by a frameless torque motor and the transmission is replaced by direct dri
Read More
28 - 10
DATE
2026
Magnetic Pole Pairs: Too Many Is Wasteful, Too Few Is Insufficient—Where Are The Selection Limits of Injection-Molded Ferrite Disks?
When selecting magnetic encoder disks, a common intuition is: the higher the number of pole pairs, the higher the resolution and the better the performance. At the sensor level, this judgment is broadly valid. But once the magnet material is fixed as injection-molded ferrite, the situation becomes m
Read More
28 - 10
DATE
2026
Axial-Flux Rotor Magnet Demagnetization Temperature Selection: Temperature Is The First Subject of Selection
The most common mistake in magnet selection for axial-flux motors is to start from the grade table: first look at remanence, then at the maximum operating temperature, and pick a grade that is “good enough” to put into the BOM. But in an axial-flux structure, this order is exactly reversed. The roto
Read More
23 - 10
DATE
2026
The “Size Triangle” of High-Speed Rotors: Outer Diameter, Stack Length, And Shaft Diameter—Why You Can’t Max Out All Three at Once
A high-speed motor or flywheel rotor sits in front of you. Outer diameter, stack length, shaft diameter—three numbers that seem like nothing more than annotations on a drawing. But in the world of high-speed rotation, these three dimensions constrain one another and form a triangle that can almost n
Read More
23 - 10
DATE
2026
Selsyn Mechanical Interface Selection: Shaft Diameter, Flange And Mounting Dimensions—Precision Can Collapse with The Smallest Deviation
When the electrical parameters of a resolver are selected correctly, the system may still exhibit angle fluctuation and zero-position drift. The problem is often not in the decoding circuit but in a more hidden place: the mechanical interface. A resolver essentially measures angle through electromag
Read More
14 - 10
DATE
2026
Temperature Rise And Demagnetization of Frameless Torque Motors
1. A Counterintuitive Phenomenon: Why Is Slower More Dangerous?For many engineers, the intuition is that the faster a motor runs, the hotter it gets. But in the world of frameless torque motors, this logic is exactly reversed.A frameless torque motor has no housing, no bearings, and no output shaft.
Read More
14 - 10
DATE
2026
Comparison of Single-Track And Dual-Track Magnetic Encoder Disks
In industrial automation, robot joint control, and new energy vehicle motor systems, magnetic encoders are playing an increasingly critical role. Through non-contact magnetic field sensing, they convert rotary or linear motion into precise electrical signals, providing the system with position, spee
Read More
  • Total 35 pages  Go to Page
  • Go
Facebook
Twitter
LinkedIn
Instagram

WELCOME

SDM Magnetics is one of the most integrative magnet manufacturers in China. Main products : Permanent magnet,Neodymium magnets,Motor stator and rotor, Sensor resolvert and magnetic assemblies.
  • Add
    108 North Shixin Road, Hangzhou, Zhejiang 311200 P.R.China
  • E-mail
    inquiry@magnet-sdm.com​​​​​​​

  • Landline
    +86-571-82867702